Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterPanel Replacement in Hempstead, NY
Garage door panel replacement in Hempstead typically runs $250 – $650 per panel, with most jobs completed same-day once the panel is in hand. We replace dented, rusted, or impact-damaged panels on all major door brands, and the new panel is matched to your existing door’s profile so it sits flush and operates clean. Call (516) 559-5490 and we’ll come out, measure the door, and put a written price in your hand before any work starts. This is a focused service under our broader Garage Door Repair work in Hempstead, and we run it to the same standard as every other job we take.
We’re Brock Garage Doors Hempstead, an independently owned location operating under the Garrison Partners network. Every panel job leaves our truck with the 365-Day Done Right Promise in writing: if the panel work fails within a full year, we return and make it right at no charge. That’s not a verbal assurance. It’s on paper.
When You Need Panel Replacement
A bent or broken panel isn’t always a full door replacement problem. Here’s what tells us the panel itself needs to go:
- Impact damage from a vehicle. A car or mower bump leaves a crease that can’t be straightened without weakening the steel. In Hempstead, with tight driveways and attached garages, this is the most common call we get. The panel gets replaced; the rest of the door stays.
- Rust or corrosion that’s eaten through the panel face. Salt air off Long Island works on steel doors. Once rust perforates the metal, patching buys you months, not years. A new panel restores the door’s structural rigidity.
- A crack running across a panel on a wood door. Freeze-thaw cycles in Nassau County winters split wood panels that have lost their seal. If the crack extends to the stile, the panel needs replacing before it fails outright.
- Section separation. When the weatherstripping or rail between panels has buckled, the door loses its thermal seal and its smooth tracking. Replacing the affected section stops the rattle and the draft.
- Fading or peeling that’s cosmetic but structural. On steel doors, deep scratches that expose bare metal eventually rust. If you’re selling a home in Hempstead, a clean panel set matters. We can match the panel color and profile on most major brands.
- The door still works but one section is warping. A warped panel puts uneven load on the hinges and the spring. Fix it now and you avoid a spring job later.
If you’re not sure whether the panel alone is the right fix or the whole door has had it, call us. We’ll tell you straight which one makes sense for the money, and you’ll have that answer in writing. For broader door issues, our Garage Door Repair in Hempstead page covers the full scope.
Our Panel Replacement Process
We keep the steps simple because that’s what a disciplined job looks like. Here’s how it runs:
- You call (516) 559-5490. A live person answers, 24/7. We take your address in Hempstead, note the door brand if you know it, and set a window. We show up in that window.
- We measure and identify the door. For Wayne Dalton, Craftsman, Raynor, and LiftMaster doors, we identify the exact panel profile, thickness, and color. Getting the profile right is the difference between a panel that sits flush and one that looks like an afterthought.
- We hand you a written price. Before a single bolt turns, you get the number for the panel, any trim, and labor. No “we’ll see how it goes.” No phone call later revising the figure. The price you approve is the price on the invoice.
- We remove the damaged panel and install the matched replacement. The work is done by a background-checked, uniformed technician who has passed a background check. The door gets tested through a full cycle, hinges and rollers checked for play, and the tension verified.
- We walk you through the work before we leave. You’ll see the panel seated, the door balanced, and the site clean. Then we hand you the written 365-Day Done Right Promise. If that repair fails within a year, we come back at no charge.
That’s the Garrison Standard. It’s not marketing copy; it’s the operating rule: show up in the window, price in writing, do it by the book, leave it clean, stand behind it for a year.
Panel Replacement Pricing in Hempstead
Most single panel replacements in Hempstead run $250 – $650, installed. The range is driven by four things:
- Panel profile and brand. A plain raised steel panel on a common door sits at the lower end. A panel for a Raynor or Wayne Dalton residential line with a specific emboss pattern runs higher. We don’t mark up parts arbitrarily; the profile dictates the part cost.
- Number of panels. Damage often skips across multiple sections. Replacing two panels isn’t double the labor because the truck’s already there, but the part cost adds up. A two-panel job usually lands between $450 and $1,100.
- Door size and thickness. A 16-foot door panel costs more than a 9-foot panel. Insulated panels cost more than non-insulated ones, but they also restore the door’s thermal break, which matters in a Hempstead winter.
- Hardware condition. If the hinges, rollers, or weatherseal on the affected section are worn, we’ll include that in the written price so you’re not surprised. We don’t do the work and bill you after.
Here’s the honest range for the most common jobs we see in the area:
| Job Type | Typical Price Range |
|---|---|
| Single steel panel replacement | $250 – $450 |
| Single insulated panel replacement | $350 – $650 |
| Two-panel replacement | $450 – $1,100 |
| Panel plus hinge/roller replacement | $300 – $700 |
All estimates are free. Call (516) 559-5490, and we’ll come measure, identify the panel, and give you a written number. You’re not obligated to say yes, and we won’t pressure you to.
FAQs – Panel Replacement
Can you match my existing panel, or will it look different?
Yes, we match the panel profile, thickness, and color for the major brands we service, including Wayne Dalton, Craftsman, and Raynor. A 15-year-old door won’t match perfectly finish-for-finish because of UV fade, but the profile lines up so it sits flush and tracks without binding. We’ll show you the panel match before we install it. Call (516) 559-5490 and we’ll check the profile on your door.
Is it cheaper to replace one panel or the whole door?
If one or two panels are damaged and the rest of the door, the springs, and the tracks are sound, replacing the panel is almost always the cheaper move. A full door replacement in Hempstead typically runs $1,200 – $3,500 installed, against $250 – $650 for a single panel. The exception is a door past its service life, where the springs are worn, the sections are faded, and the bottom seal is shot. We’ll tell you straight which one applies to your door, and you’ll have the comparison in writing before you decide.
Do you replace panels on wood garage doors?
Yes. We replace wood panels where the structure is still sound and the damage is limited to one or two sections. This shows up in Hempstead older homes with original wood doors; the panels split along the grain after years of Long Island humidity and freeze-thaw cycling. We’ll assess the stiles and rails before recommending panel replacement, because a wood door with rot in the frame isn’t a panel job, it’s a door job. We’ll tell you which one it is.
Can you come today?
In most cases, yes. Panel replacement is a same-day job once the correct panel is identified and sourced. Local suppliers keep common profiles in stock, and we carry the common fasteners and hardware on the truck. A live person answers the phone around the clock, so call (516) 559-5490 and we’ll give you a real window, not a callback. We can also discuss sensor calibration if your door has safety issues.
What’s the guarantee on a panel replacement?
Every panel replacement carries the 365-Day Done Right Promise in writing. If the panel work fails within one year, we return and correct it at no charge. That includes a free second visit. We don’t make the guarantee a fee item or a negotiation; it’s part of the job, and you get it on paper before the work starts.
Why Hempstead Calls Brock for Panel Work
We’ve been operating as part of the Garrison Partners network since 2001. That’s two decades of a simple rule: the price goes in writing before the work starts, and the guarantee goes in writing before the truck leaves. Wade Mercer runs this location to that standard. Our technicians are background-checked and uniformed, trained on eight major brands including LiftMaster, Wayne Dalton, Craftsman, and Raynor. When a real person answers at 3 a.m. because your door is stuck open with a bent panel, that’s not a call center. That’s us.
For anything beyond panel work, see our Garage Door Repair in Hempstead page. If you need a panel matched and the door running right, call (516) 559-5490 now for a free estimate.
Written by Wade Mercer, Owner at Brock Garage Doors Hempstead, serving Hempstead.